Theo dõi
Raul Payri
Raul Payri
CMT-Clean Mobility&Thermofluids, Universitat Politecnica de valencia
Email được xác minh tại mot.upv.es - Trang chủ
Tiêu đề
Trích dẫn bởi
Trích dẫn bởi
Năm
IJER editorial: The future of the internal combustion engine
RD Reitz, H Ogawa, R Payri, T Fansler, S Kokjohn, Y Moriyoshi, ...
International Journal of Engine Research 21 (1), 3-10, 2020
8302020
The influence of cavitation on the internal flow and the spray characteristics in diesel injection nozzles
F Payri, V Bermúdez, R Payri, FJ Salvador
Fuel 83 (4-5), 419-431, 2004
6102004
Using spray momentum flux measurements to understand the influence of diesel nozzle geometry on spray characteristics
R Payri, JM García, FJ Salvador, J Gimeno
Fuel 84 (5), 551-561, 2005
5232005
Diesel nozzle geometry influence on spray liquid-phase fuel penetration in evaporative conditions
R Payri, FJ Salvador, J Gimeno, LD Zapata
Fuel 87 (7), 1165-1176, 2008
2642008
Development and validation of a theoretical model for diesel spray penetration
JM Desantes, R Payri, FJ Salvador, A Gil
Fuel 85 (7-8), 910-917, 2006
2632006
The role of hydrogen for future internal combustion engines
A Onorati, R Payri, BM Vaglieco, AK Agarwal, C Bae, G Bruneaux, ...
International Journal of Engine Research 23 (4), 529-540, 2022
2432022
Engine combustion network: comparison of spray development, vaporization, and combustion in different combustion vessels
M Bardi, R Payri, LMC Malbec, G Bruneaux, LM Pickett, J Manin, T Bazyn, ...
Atomization and Sprays 22 (10), 2012
2282012
New technique for determination of internal geometry of a diesel nozzle with the use of silicone methodology
V Macián, V Bermúdez, R Payri, J Gimeno
Experimental techniques 27, 39-43, 2003
2052003
Influence of cavitation phenomenon on primary break-up and spray behavior at stationary conditions
JM Desantes, R Payri, FJ Salvador, J De la Morena
Fuel 89 (10), 3033-3041, 2010
2012010
Engine Combustion Network (ECN): Characterization and comparison of boundary conditions for different combustion vessels
M Meijer, B Somers, J Johnson, J Naber, SY Lee, LMC Malbec, ...
Atomization and Sprays 22 (9), 2012
1992012
Effects of nozzle geometry on direct injection diesel engine combustion process
R Payri, FJ Salvador, J Gimeno, J De la Morena
Applied thermal engineering 29 (10), 2051-2060, 2009
1932009
Study of cavitation phenomena based on a technique for visualizing bubbles in a liquid pressurized chamber
R Payri, FJ Salvador, J Gimeno, J De la Morena
International Journal of Heat and Fluid Flow 30 (4), 768-777, 2009
1882009
Experimental characterization of diesel ignition and lift-off length using a single-hole ECN injector
J Benajes, R Payri, M Bardi, P Martí-Aldaraví
Applied thermal engineering 58 (1-2), 554-563, 2013
1832013
Engine combustion network (ECN): measurements of nozzle geometry and hydraulic behavior
AL Kastengren, FZ Tilocco, CF Powell, J Manin, LM Pickett, R Payri, ...
Atomization and Sprays 22 (12), 2012
1822012
A NEW METHODOLOGY FOR CORRECTING THE SIGNAL CUMULATIVE PHENOMENON ON INJECTION RATE MEASUREMENTS.
R Payri, FJ Salvador, J Gimeno, G Bracho
Experimental techniques 32 (1), 2008
1822008
Analysis of the influence of diesel nozzle geometry in the injection rate characteristic
J Benajes, JV Pastor, R Payri, AH Plazas
J. Fluids Eng. 126 (1), 63-71, 2004
1702004
Fuel temperature influence on diesel sprays in inert and reacting conditions
R Payri, JM García-Oliver, M Bardi, J Manin
Applied Thermal Engineering 35, 185-195, 2012
1662012
The effect of temperature and pressure on thermodynamic properties of diesel and biodiesel fuels
R Payri, FJ Salvador, J Gimeno, G Bracho
Fuel 90 (3), 1172-1180, 2011
1582011
A contribution to the understanding of cavitation effects in Diesel injector nozzles through a combined experimental and computational investigation
F Payri, R Payri, FJ Salvador, J Martínez-López
Computers & Fluids 58, 88-101, 2012
1532012
Measurements of Spray Momentum for the Study of Cavitation in Diesel Injection Nozzles
JM Desantes, R Payri, FJ Salvador, J Gimeno
SAE SP, 77-86, 2003
1522003
Hệ thống không thể thực hiện thao tác ngay bây giờ. Hãy thử lại sau.
Bài viết 1–20