Folgen
Dr.TTM.KANNAN
Dr.TTM.KANNAN
PRIST DEEMED TO BE UNIVERSITY
Bestätigte E-Mail-Adresse bei prist.ac.in
Titel
Zitiert von
Zitiert von
Jahr
Recycling of plastic waste into fuel by pyrolysis-a review
KK Jha, TTM Kannan
Materials Today: Proceedings 37, 3718-3720, 2021
1022021
Scope of 3D printing in manufacturing industries-A review
B Sandeep, TTM Kannan, J Chandradass, M Ganesan, AJ Rajan
Materials Today: Proceedings 45, 6941-6945, 2021
462021
Optimization of cylindrical grinding parameters of austenitic stainless steel rods (AISI 316) by Taguchi method
K Mekala, J Chandradas, K Chandrasekaran, TTM Kannan, E Ramesh, ...
International journal of mechanical engineering and robotics research 3 (2), 208, 2014
382014
Effect of silicon carbide and silicon carbide/alumina reinforced aluminum alloy (AA6061) metal matrix composite
J Chandradass, T Thirugnanasambandham, P Jawahar, TTM Kannan
Materials Today: Proceedings 45, 7147-7150, 2021
272021
Optimization of catalytic pyrolysis process for change of plastic waste into fuel
KK Jha, TTM Kannan, N Senthilvelan
Materials Today: Proceedings 39, 708-711, 2021
242021
Energy management strategy for zone cooling load demand reduction in commercial buildings: A data-driven approach
T Kannan, C Lork, W Tushar, C Yuen, NC Wong, S Tai, L Lan, KL Wood
IEEE Transactions on Industry Applications 55 (6), 7281-7299, 2019
232019
Development of computer vision for inspection of bolt using convolutional neural network
TTMK A. John Rajan, K. Jayakrishna, T. Vignesh, J. Chandradass
Material today: proceedings 1 (-), 1-5, 2021
21*2021
Alternate fuel preparation in low cost from waste plastic: A review
KK Jha, TTM Kannan
Materials Today: Proceedings 37, 3656-3657, 2021
182021
Optimization of drilling parameters on austenitic stainless steel (AISI 316) using taguchi's methodology
M Sundeep, M Sudhahar, TTM Kannan, PV Kumar, N Parthipan
International Journal of Mechanical Engineering and Robotics Research 3 (4), 388, 2014
182014
Optimization of milling parameters of OHNS steel using TiAlN coated cutter by design of experiment technique
SN Sadiq, TR Raguraman, DT Kumar, R Rajasekaran, TTM Kannan
International Journal of Mechanical Engineering and Robotic Reearch, Volume, 1, 2014
172014
Optimization of milling parameters of EN8 using Taguchi methodology
RA Raj, T Parun, K Sivaraj, TTM Kannan
International Journal of mechanical Engineering and Robotics Research 2, 202-208, 2013
152013
Influence of blends of castor seed biodiesel and diesel on engine characteristics
TTMK Ameren Kondaiah a, Y. Sesha Rao, Satishkumar, Nitin D. Kamitkar , S ...
Materials Today: Proceedings 1 (1), 1-7, 2021
13*2021
Investigation of Vibration Analysis during end milling process of Monel alloy
TTMK Muhammed Shihan,J.Chandra dass
Material Today: Proceeedings, 2020
11*2020
Optimization of micro milling parameters of Al-6082 by anova methodology
MS Kumar, TTM Kannan, S Giridharan, PV Kumar
International Journal of Mechanical Engineering and Robotics Research 3 (4), 377, 2014
112014
Influence of load and sliding speed on wear behavior of AZ91E magnesium alloy nanocomposite by dry sliding
TTMK T. Thirugnanasambandham , J. Chandradass
Materials Today: Proceedings 2 (-), -, 2020
92020
Mechanical and surface morphology study of Monel - Copper joint by rotary friction welding
TTMK S.Marimuthu,K.R.Balasubramanian
Materials Today- Proceedings, 1-6, 2020
8*2020
Fuel from Plastic waste: A Review
AD Kundan kumar Jha, TTM.Kannan
Lecture notes in Mechanical Engineering- Springer nature, 847-851, 2021
7*2021
Experimental Investigation of Heat Partition, Tool Wear and Tool Life in Hard Turning of AISi-316 Steel Using CBN Cutting Tool Insert
TTM Kannan, R Rajasekaran, M Ganapathy, B Ashok, BS Pragash
International Journal of Mechanical Engineering and Robotics Research 3 (1 …, 2014
72014
Experimental Investigation of Silicon Carbide Nanoparticles Reinforced Magnesium Alloy (AZ91E) Metal Matrix Composite by Vacuum Stir Casting Method
KM Thirugnana Sambandham Thangavel,Chandradass Jeyaseelan and Baskara ...
SAE International 28 (0169), 1-5, 2019
6*2019
Energy Management Strategy for Zone Cooling Load Demand Reduction with Occupancy Thermal Comfort Margin
T Kannan, C Lork, W Tushar, C Yuen, NC Wong, S Tai
2019 IEEE PES GTD Grand International Conference and Exposition Asia (GTD …, 2019
62019
Das System kann den Vorgang jetzt nicht ausführen. Versuchen Sie es später erneut.
Artikel 1–20